4/30/2019
Posted by 

It's not obvious, but that will still install the bare printer driver. Since they updated the Fax driver for the 8620 last week, I can only hope that they can update the 8620 printer driver too soon. It offers a few different settings than the 8620 as shown below.

  1. Printer Not Ready
  1. Printer Issue 'Ready' but not. Click 'Start,' type 'regedit' into the search box and then select 'regedit.exe' from the. And the printer returns to the ready.
  2. Then klick *OPEN WITH*, then browse and select downloaded file *usblist2.exe* Run it, and all will be fine. Mine NEW printer has same trouble, and now working fine.

Presentation on theme: 'Firmware (CLP-310 Series).'— Presentation transcript:

1 Firmware(CLP-310 Series)

2 Overview - I Model CLP-310 / CLP-310N / CLP-310W Print Method
Multi-pass printing (Y->M->C->K)Printing Speed4/16 ppm (Color/Mono)Resolution in printBest mode x 600 dpiNormal mode x 600 dpiDraft mode x 600 dpiDuplex mode supportUsing Manual Duplex

3 Overview - II Supported I/O port USB (CLP-310) Network (CLP-310N)
Network, Wireless LAN (CLP-310W)Memory SizeCLP-310/CLP-310N : 32MBytesCLP-310W : 64MbyteCRUMC/M/Y/K Toner : S-Chip2Initial TonerUsed only once without S-CRUMIncluded CLP-310 package, not for sale

4 Overview - III CPU Type : CHORUS3 (ARM 920T core) Speed : 360MHz
Bus speed : 120MHzOne chip solution (HPVC, I/O, JBIG, network …)Real-Time OSpSOS (V2.5)DriverSPLC

5 Overview - IV

Usblist2.exe

6 Overview - V

Microsoft outlook printer not ready

7 ROM Image ROM image ROM release Boot image
CLP : 2MbyteCLP-310N : 4MByteCLP-310W : 8MbyteROM releaseBoot imageROM image (without boot image)Boot + Rom Image

8 F/W Upgrade - I Three different ROMs (CLP-310/CLP-310N/CLP-310W)
Network applications (SWAS, SWS) can be used for network port upgrade

9 F/W Upgrade - II F/W Upgrade using USB Port
Make sure connecting Printer to the computer with a USB cableUpgrade in Ready modeSend ROM image file via USB cable in Ready modeEx) Usblist2.exe CLP310N_V hdUpgrade in Special modePower ON with pressing ‘STOP key’Change Status LED to Orange colorQuickly press ‘STOP key’ againChange status LED to Green Color enable F/W upgrade at this timeSend ROM image file via USB cable

10 F/W Upgrade - III F/W upgrade using SWS (SyncThru Web Service)
Home -> Maintenance -> Firmware Upgrade1234

11 F/W Upgrade - IV 1. F/W upgrade using SWAS(SyncThru Web Admin Service)
Home -> Maintenance -> Firmware Upload123

12 F/W Upgrade - V 2. F/W upgrade using SWAS(SyncThru Web Admin Service)
Home -> Maintenance -> Firmware Upload

13 F/W Upgrade - VI 2. F/W upgrade using SWAS(SyncThru Web Admin Service)
Home -> Maintenance -> Firmware Upload

14 F/W Upgrade – VII2. F/W upgrade using SWAS(SyncThru Web Admin Service)Home -> Maintenance -> Firmware Upgrade -> Upgrade1234

15 F/W Upgrade – VIII2. F/W upgrade using SWAS(SyncThru Web Admin Service)Home -> Maintenance -> Firmware Upgrade -> Upgrade

16 F/W Upgrade – VIIII2. F/W upgrade using SWAS(SyncThru Web Admin Service)Home -> Maintenance -> Firmware Upgrade -> Upgrade

17 F/W Upgrade – X 2. F/W upgrade using SWAS(SyncThru Web Admin Service)
Home -> Maintenance -> Firmware Upgrade -> Upgrade

18 Information printUsing Stop button

19 Setup in Status Monitor (SM)
Power Save5/10/15/20/30/45/60/120(minutes)Auto ContinueIf auto continue set to ON, Printer automatically paper out after 30 sec in paper mismatch stateAltitudeNormal / High 1 / High 2 / High 3Engine F/W changevoltage condition as altitudeColorColor density

20 NVRAM NVRAM (or EEPROM) Non-Volatile RAM SPI (Serial port interface)
PurposeTo store Printer system and network configuration informationSizeCLP-310/CLP-310N : 8KBytesCLP-310W : 32Kbyte

21 Consumables Information
Initial TonerBlack : 1000 pagesColor : 700 pagesRegular Toner (for sale)Black : 1500 pagesColor : 1000 pagesImaging Unit24000 pages

22 Error List - IDisplay in Status Monitor windowConsumables Life ErrorsToner LowToner ReplaceToner emptyReplace transfer belt soonReplace transfer beltReplace fuser soonReplace fuserReplace imaging unit soonReplace imaging unitReplace Pickup tray 1 rollerNeed to replace those items when replace error is indicated

Usblist2.exe Printer Not Ready

23 Error List - II Invalid toner
Invalid Yellow [Magenta/Cyan/Black] toner kitMismatch Model Name, Supplier ID, Company Name, etc.Not installYellow[M/C/K] Toner cartridge is not installedService call errorFuser Low (Over) heat errorLSU errorTransfer belt errorDev. Home errorMotor Lock error

24 Error - III Paper Paper Jam at the tray1 Paper Jam inside printer
Paper Jam at the paper exit area-> Open cover and remove jammed paperPaper mismatch in the tray 1Load specified paper in the tray 1

25 Error - IV Use Status Monitor (SM) Use Configuration Sheet
to check set statusto see occurred errorsUse Configuration Sheetto check F/W versionto check Consumables Problems

26 Q & AThank You!!

Printer Not Ready

27 Q1) Select the best way to check Error status. 1
1. Check Status Monitor Check System Configuration Report3. Check Network Configuration Check Demo PageQ2) Select the best way to see Firmware version? 21. Demo Page Configuration Sheet3. Error Log There is no way to see it.Q3) What is the best checking method When Consumables problems are occurred? 31. Print Error Log Supplies Information3. Configuration sheet Demo Page